Specifications
All specifications are guaranteed unless noted otherwise. All specifications apply to all models unless noted otherwise.
Channels
- Number of channels
- 2
Built-in waveforms
- Built-in waveforms
- Sine, Square, Pulse, Ramp, Noise, and 45 frequently used arbitrary waveforms
General characteristics
- Sine waves
-
- Range
-
AFG1022 AFG1062 1 μHz to 25 MHz 1 μHz to 60 MHz - Sine wave in burst mode
-
2 mHz to 25 MHz 2 mHz to 30 MHz - Effective maximum frequency out
-
25 MHz 60 MHz - Amplitude flatness (1 Vp-p), typical
- <10 MHz
-
±0.4 dB ±0.5 dB - ≥10 MHz and ≤25 MHz
-
±0.7 dB - ≥10 MHz and ≤60 MHz
-
±0.9 dB - Harmonic distortion (1 Vp-p)
- ≤10 MHz
-
< -50 dBc < -60 dBc - >10 MHz
-
< -50 dBc < -47 dBc - Total harmonic distortion
-
< 0.2% (10 Hz to 20 kHz, 1 Vp-p) - Spurious (1 Vp-p), typical
-
< -45 dBc - Phase noise, typical
-
1 MHz: < -110 dBc/Hz at 10 kHz offset, 1 Vp-p - Residual clock noise, typical
-
-57 dBm
- Square wave
-
- Range
-
AFG1022 AFG1062 1 μHz to 12.5 MHz 1 μHz to 30 MHz - Rise/fall time, typical
-
<12 ns <10 ns - Jitter (rms), typical
-
<1 ns <500 ps - Overshoot
-
<5%
- Ramp wave
-
- Range
-
AFG1022 AFG1062 1 μHz to 1 MHz 1 μHz to 2 MHz - Linearity, typical
-
≤ 0.1% of peak output at 10% – 90% of amplitude range, at 1 kHz, 1 V p-p , 50% symmetry - Symmetry
-
0.0% to 100.0%
- Pulse wave
-
- Range
-
AFG1022 AFG1062 1 μHz to 12.5 MHz 1 μHz to 30 MHz - Pulse width range
-
40 ns to 999 ks 17 ns to 999 ks - Pulse width resolution
-
1 ns or 4 digits - Pulse duty
-
<1 MHz, 0.1% to 99.9% (limitations of pulse duty width apply) ≥1 MHz, 50% fixed ≥1 MHz, 50% fixed - Edge transition time, typical
-
<12 ns, fixed <10 ns, fixed - Overshoot, typical
-
<5% - Jitter (rms), typical
-
<1 ns <500 ps
- Noise
-
- Noise bandwidth (-3 dB)
-
AFG1022 AFG1062 25 MHz 50 MHz - Noise type
-
White Gausian
- DC
-
- Range
-
AFG1022 AFG1062 -5 V to +5 V, 50 Ω load -10 V to + 10 V, open circuit or high Z load
- Arbitrary waveform
-
- Range
-
AFG1022 AFG1062 1 μHz to 10 MHz 1 μHz to 30 MHz - Arbitrary waveform in burst mode
-
2 mHz to 10 MHz 2 mHz to 30 MHz - Effective analog bandwidth (-3 dB)
-
30 MHz 60 MHz - Non-volatile memory
-
64 MByte - Memory
- Length
-
2 to 8,192 2 to 1 M-point - Sampling rate
-
125 MS/s 300 MS/s - Vertical resolution
-
14 bits - Rise and fall time
-
< 10 ns < 8 ns - Jitter (rms), typical
-
< 6 ns
- Frequency
-
- Resolution
-
AFG1022 AFG1062 1 μHz or 12 digits - Internal reference stability
-
±1 ppm at 0 – 40 °C - Internal reference aging
-
±1 ppm per year
- Amplitude
-
- Range (50 Ω load)
- ≤25 MHz
-
AFG1022 AFG1062 1 mVp-p to 10 Vp-p 1 mVp-p to 10 Vp-p - >25 MHz
-
– 1 mV p-p to 5 V p-p - Range (Open circuit or high Z load)
- ≤25 MHz
-
2 mVp-p to 20 Vp-p 2 mV p-p to 20 V p-p - >25 MHz
-
– 2 mV p-p to 10 V p-p - Accuracy
- ±(1% of setting +1 mVp-p), (1 kHz sine waveform, 0 V offset)
- Resolution
- 1 mVp-p, 1 mVrms or 4 digits
- Units
- Vp-p, Vrms
- Output impedance
- 50 Ω (typical)
- Local impedance setting
- Selectable: 50 Ω, 1 Ω to 10.000 kΩ, High Z (adjusts displayed amplitude according to selected load impedance)
- Isolation
- No floating ground, signal ground connected to chassis ground
- Signal output protection
- Short-circuit tolerance, main output automatically disabled when over current
DC offset
- Range
- ±(5 Vpk– Amplitudep-p/2), 50 Ω load
±(10 Vpk– Amplitudep-p/2), open circuit or high Z load
- Accuracy
- ±(1% of |setting| + 1 mV + 0.5% of amplitude (Vp-p))
- Resolution
- 1 mV or 4 digits
Modulation
Modulation, sweeping, and burst modes are only available for channel 1 on the AFG1022.
The AFG1062 supports equal strong channels with modulation, sweeping, and burst modes.
- Amplitude modulation
-
- Carrier waveforms
- Sine, square, ramp, arbitrary, except DC and noise
- Source
- Internal / external
- Internal modulating waveforms
- Sine, square, ramp, noise, arbitrary
- Internal AM frequency
- 2 mHz to 20 kHz
- Depth
- 0.0% to 100.0%
- Frequency modulation
-
- Carrier waveforms
- Sine, square, ramp, arbitrary, except DC and noise
- Source
- Internal / external
- Internal modulating waveforms
- Sine, square, ramp, noise, arbitrary
- Internal modulating frequency
- 2 mHz to 20 kHz
- Frequency deviation
- (limited by carrier waveform type)
AFG1022 AFG1062 2 mHz to 12.5 MHz 2 mHz to 30 MHz
- Phase modulation
-
- Carrier waveforms
- Sine, square, ramp, arbitrary, except DC and noise
- Source
- Internal / external
- Internal modulating waveforms
- Sine, square, ramp, noise, arbitrary
- Internal PM frequency
- 2 mHz to 20 kHz
- Phase Deviation
- 0° to 180°
- Amplitude shift keying
- (AFG1062 only)
- Carrier waveforms
- Sine, square, ramp, arbitrary, except DC and noise
- Source
- Internal / external
- Internal modulating waveforms
- 50% duty cycle square
- ASK rate
- 2 mHz to 100 kHz
- Frequency shift keying
-
- Carrier waveforms
- Sine, square, ramp, arbitrary, except DC and noise
- Source
- Internal / external
- Internal modulating waveforms
- 50% duty cycle square
- FSK rate
- 2 mHz to 100 kHz
- Phase shift keying
- (AFG1062 only)
- Carrier waveforms
- Sine, square, ramp, arbitrary, except DC and noise
- Source
- Internal / external
- Internal modulating waveforms
- 50% duty cycle square
- PSK rate
- 2 mHz to 100 kHz
- Pulse width modulation
- (AFG1062 only)
- Carrier waveforms
- Pulse, ≤1 MHz
- Source
- Internal / external
- Internal modulating waveforms
- Sine, square, ramp, arbitrary, except DC and noise
- PWM frequency
- 2 mHz to 20 kHz
- Deviation
- 0.0% to 50.0% of pulse period
Sweeping
Modulation, sweeping, and burst modes are only available for channel 1 on the AFG1022.
The AFG1062 supports equal strong channels with modulation, sweeping, and burst modes.
- Carrier waveforms
- Sine, square, ramp, arbitrary (AFG1062 only)
- Minimum start-stop frequency
- 1 μHz
- Maximum start-stop frequency
-
- Sine
-
AFG1022 AFG1062 25 MHz 60 MHz - Square
-
12.5 MHz 30 MHz - Ramp
-
1 MHz 2 MHz
- Type
- Linear, logarithmic
- Direction
- Up / down
- Sweep time
- 1 ms to 500 s ± 0.1%
- Trigger sources
- Internal, external, or manual
Burst
Modulation, sweeping, and burst modes are only available for channel 1 on the AFG1022.
The AFG1062 supports equal strong channels with modulation, sweeping, and burst modes.
- Waveforms
- Sine, square, ramp, pulse, arbitrary except DC and noise
- Types
- AFG1022: count (1 to 50,000 cycles), infinite, gated
AFG1062: count (1 to 1,000,000 cycles), infinite, gated
- Start phase
- -360° to +360°
- Trigger sources
- Internal, external, or manual
- Internal trigger interval
- (40 ns or (cycles x period) to 500 s) ± 1%
- Gate source
- External trigger
Frequency counter
- Function
- Frequency, period, positive pulse width, duty cycle
- Frequency range
- 100 mHz to 200 MHz
- Frequency resolution
- 6 digits
- Coupling mode
- AC, DC
- Voltage Range and Sensitivity, DC coupled (non-modulation signal)
-
- 100 mHz to 100 MHz
- 250 mVp-p to 5 Vp-p (AC + DC)
- 100 MHz to 200 MHz
- 450 mVp-p to 3 Vp-p (AC + DC)
- Voltage range and sensitivity, AC coupled (non-modulation signal)
-
- 1 Hz to 100 MHz
- 250 mVp-p to 5 Vp-p
- 100 MHz to 200 MHz
- 450 mVp-p to 4 Vp-p
- Pulse width and duty cycle measure
- 1 Hz to 10 MHz
- Input impedance
- 1 M Ω in parallel with 100 pF
- High frequency noise restraint (HFR)
- On / Off (HFR frequency = 500 kHz)
- Sensitivity
- Low, middle, or high
- Trigger level range
- -2.5 V to +2.5 V
Auxiliary inputs and outputs
- External modulation input
-
- Input frequency range
- DC to 20 kHz
- Input voltage range
- All except FSK: ±1 V full scale, FSK: 3.3 V logic level
- Input impedance
- 12 kΩ (typical)
- External trigger input
-
- Level
- TTL-compatible
- Slope
- Rising or falling (selectable)
- Pulse Width
- >100 ns
- External reference clock input
- (Shared with Frequency Counter Input)
- Impedance
- 400 Ω, AC coupled
- Requested Input voltage swing
- 100 mVp-p to 5 Vp-p
- Locking range
- 10 MHz ±9 kHz
- External reference clock output
-
- Frequency
- 10 MHz
- Impedance
- 50 Ω, DC coupled
- Amplitude
- 1.6 Vp-p into 50 Ω load
- Communication interface
-
- USB
- Host and device, USB TMC compliance
Display
- Display type
- 3.95-inch
- Display resolution
- 480 by 320
- Display colors
- 65,536
Menu and online help languages
- Menu and online help languages
- English and Simplified Chinese
Power source
- Supply
- 220-240 VAC, 100-120 VAC, 50/60 Hz, CATⅡ
- Consumption
- AFG1022: Less than 28 W
AFG1062: Less than 35 W
- Fuse
- 110 V: 250 V, F1AL
220 V: 250 V, F0.5AL
- Warm-up time
- 30 minutes (typical)
Physical characteristics
- Dimensions (W, H, D)
- 230 × 110 × 306 mm (9.0 × 4.4 × 12.1 in)
- Weight
-
- Net
- 3.4 kg (7.5 lbs)
- Shipping
- 4.7 kg (10.3 lbs)
EMC environment and safety
- Temperature
-
- Working
- 0 ℃ to 40 ℃ (32 °F to 104 °F)
- Storage
- -20 ℃ to 60 ℃ (-4 °F to 144 °F)
- Relative humidity (non-condensing)
- Operating: ≤ 80%, +0 °C to +40 °C (+32 °F to +104 °F)
Non-operating: 5% to 90%, < +40 °C (+104 °F)
Non-operating: 5% to 80%, ≥ +40 °C (+104 °F) to ≤ +60 °C (+140 °F)
- Altitude
- Operating: up to 3,000 m (9843 ft.)Non-operating: up to 12,000 m (39,370 ft)
- Cooling method
- Fan cooling
- EMC compliance
-
- European Union
- EN 61326-1
- Australia/NZ
- CISPR 11, Class A
- Safety compliance
-
- UL 61010-1
- CAN/CSA-C22.2 No. 61010-1
- EN 61010-1
- IEC 61010-1
