AFG31252 Arbitrary Function Generator

Model: Liên hệ

Price: Contact

Available: call

Call

Hà Nội: (024) 35.381.269

Specifications

All specifications are guaranteed unless noted otherwise. All specifications apply to all models unless noted otherwise.

Model overview
Model Sine frequency range Number of channels
AFG31021 25 MHz 1
AFG31051 50 MHz
AFG31101 100 MHz
AFG31151 150 MHz
AFG31251 250 MHz
AFG31022 25 MHz 2
AFG31052 50 MHz
AFG31102 100 MHz
AFG31152 150 MHz
AFG31252 250 MHz
Output characteristics
Amplitude
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
Range (into 50 Ω) ≤ 60 MHz: 1 mVP-P to 10 VP-P
> 60 MHz to ≤ 80 MHz: 1 mVP-P to 8 VP-P
> 80 MHz to ≤ 100 MHz: 1 mVP-P to 6 VP-P		 ≤ 200 MHz: 1 mVP-P to 5 VP-P
> 200 MHz to ≤ 250 MHz: 1 mVP-P to 4 VP-P
Range (into open circuit or High-Z) ≤ 60 MHz: 2 mVP-P to 20 VP-P
> 60 MHz to ≤ 80 MHz: 2 mVP-P to 16 VP-P
> 80 MHz to ≤ 100 MHz: 2 mVP-P to 12 VP-P		 ≤ 200 MHz: 2 mVP-P to 10 VP-P
> 200 MHz to ≤ 250 MHz: 2 mVP-P to 8 VP-P
Accuracy ± (1% of setting +1 mVP-P)
(1 kHz sine, 0 V offset, amplitude > 1 mVP-P)
Resolution 0.1 mVP-P, 0.1 mVRMS, 1 mV, 0.1 dBm or 4 digits
Units Vpp, Vrms (excluding Arb and Noise), dBm (sine wave only), Volt (High Level and Low Level)
Offset
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
Range (into 50 Ω) ±(5 VPK – AmplitudeP-P ÷ 2) ±(2.5 VPK – AmplitudeP-P ÷ 2)
Range (into open circuit or High-Z) ±(10 VPK – AmplitudeP-P ÷ 2) ±(5 VPK – AmplitudeP-P ÷ 2)
Accuracy ± (1% of |setting| +1 mV + 0.5% of Amplitude (VP-P))
Resolution 1 mV or 4 digits
Output impedance
50 Ω
Load impedance setting
Selectable: 50 Ω, 1 Ω to 10.0 kΩ, High Z (Adjusts displayed amplitude according to selected load impedance)
Isolation
42 Vpk maximum to earth ground
Short-circuit protection
Signal outputs are robust against permanent shorts against floating ground
Overcurrent protection
When incoming current is greater than 250 mA, the output channels are protected with relays that disconnect the AFG from the device under test. Connection can be resumed by user after removing the incoming current
General characteristics – Basic mode
Basic (AFG)
Run modes
Continuous, Modulation, Sweep and Burst
Standard waveforms
Sine, Square, Pulse, Ramp, More (Noise, DC,Sin(x)/x, Gaussian, Lorentz, Exponential Rise, Exponential Decay, Haversine )
Arbitrary waveforms
Sampling clock: 250 MSa/s, 1 GSa/s or 2 GSa/s (model and waveform length apply)Vertical resolution: 14 bits

Waveform length: 2 to 131,072 points

Sine
Frequency range
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
Continuous mode 1 μHz to 25 MHz 1 μHz to 50 MHz 1 μHz to 100 MHz 1 μHz to 150 MHz 1 μHz to 250 MHz
Burst mode 1 μHz to 12.5 MHz 1 μHz to 25 MHz 1 μHz to 50 MHz 1 μHz to 75 MHz 1 μHz to 125 MHz

 

Effective maximum frequency out
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
25 MHz 50 MHz 100 MHz 150 MHz 250 MHz

 

Amplitude flatness (1 VP-P, relative to 1 kHz)
Frequency range AFG31021, AFG31022, AFG31051, AFG31052, AFG31101, AFG31102 AFG31151, AFG31152, AFG31251, AFG31252
< 5 MHz ±0.2 dB ±0.2dB
≥ 5 MHz to 25 MHz —– ±0.3 dB
≥ 5 MHz to 100 MHz ±0.3 dB —–
> 25 MHz to 100 MHz —– ±0.5 dB
> 100 MHz to 200 MHz —– ±1.0 dB
> 200 MHz to 250 MHz —– ±2.0 dB

 

Amplitude flatness (1 VP-P, relative to 1 kHz), typical
AFG31021, AFG31022, AFG31051, AFG31052, AFG31101, AFG31102, AFG31151, AFG31152 AFG31251 / AFG31252
±0.1 dB ≤ 150 MHz: ±0.1 dB
> 150 MHz to 250 MHz: ±0.3 dB

 

Harmonic distortion (1 VP-P), typical
Frequency range AFG31021, AFG31022, AFG31051, AFG31052, AFG31101, AFG31102
10 Hz to <20 kHz < -77 dBc
≥20 kHz to <1 MHz < -72 dBc
≥1 MHz to <5 MHz < -65 dBc
≥5 MHz to ≤100 MHz < -56 dBc

 

Frequency range AFG31151, AFG31152, AFG31251, AFG31252
10 Hz to < 1 MHz < -72 dBc
≥ 1 MHz to < 5 MHz < -74 dBc
≥ 5 MHz to < 25 MHz < -69 dBc
≥ 25 MHz to ≤ 250 MHz < -37 dBc
THD, typical
≤ 0.04%, 10 Hz to 20 kHz, 1 VP-P 
Spurious noise (1 VP-P), typical
Frequency range AFG31021, AFG31022, AFG31051, AFG31052, AFG31101, AFG31102
≥ 10 Hz to < 1 MHz < -78 dBc
≥ 1 MHz to < 25 MHz < -73 dBc
≥ 25 MHz to ≤ 100 MHz < -78 dBc

 

Frequency range AFG31151, AFG31152, AFG31251, AFG31252
10 Hz to < 1 MHz < -80 dBc
≥ 1 MHz to < 25 MHz < -75 dBc
≥ 25 MHz to ≤ 250 MHz < -75 dBc + 6 dBc/octave

 

Phase noise, typical
< -125 dBc/Hz at 20 MHz, 10 kHz offset, 1 VP-P 
Residual clock noise, all models
-63 dBm 
Square
Frequency range
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
1 μHz to 20 MHz 1 μHz to 40 MHz 1 μHz to 80 MHz 1 μHz to 120 MHz 1 μHz to 160 MHz

 

Rise/fall time, typical
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
Amplitude ≤ 5 Vpp ≤ 7.0 ns ≤ 5.0 ns ≤ 3.5 ns ≤ 3.0 ns ≤ 2.0 ns
Amplitude > 5 Vpp ≤ 8.0 ns ≤6.0 ns ≤ 4.2 ns —– —–

 

Overshoot, typical
< 3% 
Jitter (RMS), typical
2.5 ps 
Ramp
Frequency range
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
1 μHz to 500 kHz 1 μHz to 800 kHz 1 μHz to 1 MHz 1 μHz to 1.5 MHz 1 μHz to 2.5 MHz

 

Linearity, typical (1 kHz, 1 VP-P, 100% symmetry)
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
≤ 0.1% of peak output ≤ 0.1% of peak output ≤ 0.15% of peak output ≤ 0.2% of peak output ≤ 0.2% of peak output

 

Symmetry
0% to 100%
Pulse
Frequency range
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
1 μHz to 20 MHz 1 μHz to 40 MHz 1 μHz to 80 MHz 1 μHz to 120 MHz 1 μHz to 160 MHz

 

Pulse width
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
16 ns to 999.99 s 10 ns to 999.99 s 6 ns to 999.99 s 4 ns to 999.99 s 3 ns to 999.99 s

 

Pulse width resolution
10 ps or 5 digits
Pulse Duty
0.001% to 99.999% (limitations of pulse width apply)
Edge transition time
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
8 ns to 0.625 * Pulse Period 6 ns to 0.625 * Pulse Period 4 ns to 0.625 * Pulse Period 3 ns to 0.625 * Pulse Period 2 ns to 0.625 * Pulse Period

 

Edge transition time resolution
10 ps or 4 digits
Lead delay range
Mode Characteristic
Continuous 0 ps to Period
Burst 0 ps to Period – [ Pulse Width + 0.8 * (Leading Edge Time + Trailing Edge Time)]

 

Lead delay resolution
10 ps or 8 digits
Overshoot, typical
< 2%
Jitter (RMS), typical
2.5 ps
DC
Range (into 50 Ω)
AFG31021, AFG31022, AFG31051, AFG31052, AFG31101, AFG31102 AFG31151, AFG31152, AFG31251, AFG31252
-5 V to 5 V -2.5 V to 2.5 V

 

Resolution (into 50 Ω)
1 mV or 4 digits
Accuracy
± (1% of |setting | +1mV)
Noise
Bandwidth (-3 dB)
AFG31021, AFG31022, AFG31051, AFG31052, AFG31101, AFG31102 AFG31151, AFG31152, AFG31251, AFG31252
150 MHz 360 MHz

 

Noise type
White Gaussian 
Internal noise
Characteristic
Add When activated, output signal amplitude is reduced to 50%
Level 0.0% to 50% of amplitude (VP-P) setting
Resolution 1%
Other waveforms
Frequency range

AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
1 μHz to 500 kHz 1 μHz to 800 kHz 1 μHz to 1 MHz 1 μHz to 1.5 MHz 1 μHz to 2.5 MHz
Arbitrary waveforms
Frequency range
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
Normal 1 mHz to 12.5 MHz 1 mHz to 25 MHz 1 mHz to 50 MHz 1 mHz to 75 MHz 1 mHz to 125 MHz
Burst mode 1 mHz to 6.25 MHz 1 mHz to 12.5 MHz 1 mHz to 25 MHz 1 mHz to 37.5 MHz 1 mHz to 62.5 MHz

 

Effective analog bandwidth (-3 dB)
AFG31021, AFG31022, AFG31051, AFG31052, AFG31101, AFG31102 AFG31151, AFG31152, AFG31251, AFG31252
150 MHz 360 MHz

 

Waveform length
2 to 131,072 
Sample rate
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
Waveform length ≤ 16,384 250 MSa/s 1 GSa/s 1 GSa/s 2 GSa/s 2 GSa/s
Waveform length > 16,384 250 MSa/s 250 MSa/s 250 MSa/s 250 MSa/s 250 MSa/s

 

Vertical resolution
14 bit 
Rise/fall time, typical
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
Amplitude ≤ 5Vpp ≤ 3.5 ns ≤ 3.5 ns ≤ 3.5 ns ≤ 2 ns ≤ 2 ns
Amplitude > 5Vpp ≤ 4.2 ns ≤ 4.2 ns ≤ 4.2 ns —– —–

 

Jitter (RMS), typical
2.5 ps 
Modulation
AM, FM, PM
Specification Characteristic
Carrier All except pulse, noise, DC
Source Internal or external
Internal modulating waveform Sine, Square, Ramp, Noise, ARB (maximum waveform length: AM 4,096 pts; FM/PM/PWM 2,048 pts)
Internal modulating frequency 1 mHz to 1 MHz

 

AM modulation depth
0.0 % to 120 % 
AM modulation resolution
0.1% 
Minimum FM peak deviation
DC 
Maximum FM peak deviation
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
Sine 12.5 MHz 25 MHz 50 MHz 75 MHz 125 MHz
Square, 10 MHz 20 MHz 40 MHz 60 MHz 80 MHz
Arb 6.25 MHz 12.5 MHz 25 MHz 37.5 MHz 62.5 MHz
Others 250 kHz 400 kHz 500 kHz 750 kHz 1.25 MHz

 

PM phase deviation range
0° to 180° 
PM phase resolution
0.1° 
FSK
Specification Characteristic
Carrier All except pulse, noise, DC
Source Internal or external
Number of keys 2
Internal key rate 1 mHz to 1 MHz

 

PWM
Specification Characteristic
Carrier Pulse
Source Internal or external
Internal modulating waveform Sine, Square, Ramp, Noise, ARB (maximum waveform length: 2,048 pts)
Internal modulating frequency 1 mHz to 1 MHz
Deviation range 0% to 50.0% of pulse period

 

Sweep
Type
Linear, Logarithmic
Waveforms
All, except Pulse, Noise, DC
Sweep time
1 ms to 500 s
Hold/return time
0 s to 500 s
Maximum total sweep time
500 sAccuracy, typical: ≤ 0.4%
Minimum start/stop frequency
All except ARB: 1 μHzARB: 1 mHz

 

Maximum start/stop frequency
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
Sine 25 MHz 50 MHz 75 MHz 125 MHz 250 MHz
Square 20 MHz 40 MHz 80 MHz 120 MHz 160 MHz
Arb 12.5 MHz 25 MHz 50 MHz 75 MHz 125 MHz
Others 500 kHz 800 kHz 1 MHz 1 MHz 2.5 MHz

 

Burst
Waveform
All except Noise, DC
Type
Triggered, gated
Burst count
1 to 1,000,000 cycles or Infinite
Intenal trigger rate
1 μs to 500.0 s
Gate and trigger sources
Internal, external, remote interface
InstaView™
Waveforms
All except noise
Cable (channel output to load)
50 Ω BNC to BNC
Run mode
Continuous in Basic mode
Maximum measurement range (DC + peak AC voltage)
AFG31021, AFG31022, AFG31051, AFG31052, AFG31101, AFG31102 AFG31151, AFG31152, AFG31251, AFG31252
-10 V to 10 V -5 V to 5 V

 

DC level measurement
Specification Characteristic
Accuracy (into 50Ω), typical ± (2 % of |setting| + 20 mVpp)
Resolution 1 mV or 4 digits

 

Amplitude measurement
Specification Characteristic
Accuracy (sine, 1 kHz, 1 VP-P, into 50 Ω, typical) ± (2 % of setting + 20 mV)
Resolution 1 mV or 4 digits

 

Bandwidth (-3 dB)
500 MHz 
Flatness, sine, 1 VP-P, into 50 ohm, relative to 1 kHz, typical
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
0 to 100 MHz: ±1 dB 0 to 200 MHz: ±1 dB
200 MHz to 250 MHz: ±2 dB

 

Cable propagation delay measurement, typical
Specification Characteristic
Range 0 to 20 ns (approximately 4 m/13 feet in length)
Accuracy, typical ± 500 ps
General characteristics – Advanced mode
Waveform memory size
16 Mpts (128 Mpts optional) each channel
Run mode
Standard: Continuous

Optional: Sequence, Triggered, Gated

Number of waveform entries
Continuous, Triggered, Gated: 1

Sequence: 1 to 256

Minimum waveform length
168 pts
Waveform granularity
1 pt
Vertical resolution
14 bits
Jump/trigger events
External trigger (rising or falling edge), manual trigger, timer, SCPI commands
Repeat count
1 to 1,000,000 or infinite
Timer range
2 µS to 3600 S
Timer resolution
4 ns or 8 digits
Variable sample rate
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
Range 1 µSa/s to 250 MSa/s 1 µSa/s to 500 MSa/s 1 µSa/s to 1 GSa/s 1 µSa/s to 2 GSa/s 1 µSa/s to 2 GSa/s
Accuracy 10-6 Sa/s
Resolution 1 µSa/s or 12 digits
Rise/Fall time, typical
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
Amplitude ≥ 5 VP-P: ≤ 4.2 ns
Amplitude < 5 VP-P: ≤ 3.5 ns		 ≤ 3.0 ns ≤ 2.0 ns
Overshoot, typical
< 2%
Level flatness, typical (sine, 1 VP-P, relative to 1 kHz)
Frequency range All models
< 5MHz ±0.3 dB
≥ 5 MHz to 25 MHz ±0.5 dB
≥ 25 MHz to 50 MHz ±0.6 dB
≥ 50 MHz to 100 MHz ±1.0 dB
≥ 100 MHz to 150 MH ±1.5 dB
≥ 150 MHz to 250 MHz ±2.3 dB

 

Harmonic distortion, typical (sine with 64 pts/cycle, 1 VP-P)
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
< -76 dBc at 250 MSa/S or 3.90625 MHz < -67 dBc at 500 MSa/S or 7.8125 MHz < -61 dBc at 1 GSa/S or 15.625 MHz < -63 dBc at 2 GSa/S or 31.25 MHz < -63 dBc at 2 GSa/S or 31.25 MHz
Spurious, typical (sine with 64 pts/cycle, 1 VP-P)
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
< -81 dBc at 250 MSa/S or 3.90625 MHz < -74 dBc at 500 MSa/S or 7.8125 MHz < -75 dBc at 1 GSa/S or 15.625 MHz < -64 dBc at 2 GSa/S or 31.25 MHz < -64 dBc at 2 GSa/S or 31.25 MHz
Spurious free dynamic range, typical (sine with 64 pts/cycle, 1 VP-P)
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
< -76 dBc at 250 MSa/S or 3.90625 MHz < -67 dBc at 500 MSa/S or 7.8125 MHz < -61 dBc at 1 GSa/S or 15.625 MHz < -63 dBc at 2 GSa/S or 31.25 MHz < -63 dBc at 2 GSa/S or 31.25 MHz
Phase noise, typical (sine with 64 pts/cycle, 1 VP-P, at 10 kHz offset)
AFG31021 / AFG31022 AFG31051 / AFG31052 AFG31101 / AFG31102 AFG31151 / AFG31152 AFG31251 / AFG31252
< -132 dBc at 250 MSa/S or 3.90625 MHz < -130 dBc at 500 MSa/S or 7.8125 MHz < -125 dBc at 1 GSa/S or 15.625 MHz < -113 dBc at 2 GSa/S or 31.25 MHz < -113 dBc at 2 GSa/S or 31.25 MHz

 

Skew control
Range
-320 ns to 320 ns (channel 1 to channel 2 on dual channel models, at maximum sample rate)
Resolution
100 ps or 4 digits
Accuracy, typical
±(1% of |setting| + 500 ps)
Initial skew, typical
< 500 ps
System characteristics
Output Frequency Resolution
Frequency accuracy
±10-6of setting (all except ARB), 0 °C to 50 °C (32 °F to 122 °F)

±10-6of setting ± 1 μHz (ARB), 0 °C to 50 °C (32 °F to 122 °F)

Aging
±1.0 x 10-6 per year
Phase
Range
-180° to +180°
Resolution
0.01° (sine)

0.1° (other waveforms)

Remote program interface
GPIB, Ethernet 10BASE-T / 100BASE-TX / 1000BASE-T, USB 2.0
Maximum configuration times, typical
USB LAN GPIB
Function change 61 ms 61 ms 63 ms
Frequency change (except Pulse) 3 ms 4 ms 6 ms
Frequency change (Pulse) 2.5 ms 3 ms 8 ms
Amplitude change 65 ms 66 ms 77 ms
Select user ARB (4k points from USB Memory) 43 ms 40 ms 53 ms
Select user ARB (128k points from USB Memory) 86 ms 92 ms 92 ms
Data download time for 4k points 36 ms 21 ms 21 ms
Power source
Source
100-240 V, 47-63 Hz115 V, 360-440 Hz
Consumption
120 W
Warm up time, typical
20 minutes minimum
Power on self diagnosis time
< 24 s
Acoustic noise
< 50 dBA
Display
9-inch capacitive touch screen with 800 * 480 resolution
User interface and Help languages
English, French, German, Japanese, Korean, Simplified and Traditional Chinese, Russian (user selectable)
Auxiliary input characteristics
External modulation input, channel 1 and channel 2
Input range
Characteristic
AM, FM, PM, PWM ±1 V full range
FSK 3.3 V logic level
Input impedance
5.2 kΩ
Frequency range
125 kHz (1 MSa/s)
External Trigger input
Level
TTL compatible
Impedance
10 kΩ
Minimum pulse width
100 ns
Slope
Positive or negative selectable
Trigger delay range
0 ns to 85 s
Trigger delay resolution
100 ps or 5 digits
Trigger latency, typical
390 ns (trigger input to signal output, , 1.5 μs for Advanced mode)
Jitter (RMS), typical
100 ps (signal output, with external trigger input in burst mode)
10 MHz reference clock input
Impedance
1 kΩ
Input coupling
AC
Required input voltage swing
100 mVP-P to 5 VP-P
Lock range
10 MHz ±35 kHz
Channel 1 external add input
Impedance
50 Ω
Input range
-1 V to +1 V (DC + peak AC)
Bandwidth
DC to 10 MHz (-3 dB) at 1 VP-P
Auxiliary output characteristics
Channel 1 trigger output
Level
Positive TTL level pulse into 1 kΩ
Impedance
50 Ω
Jitter, RMS, typical
10 ps for all models 
Output frequency
Characteristic
Waveform frequency < 4.9 MHz Same as the waveform frequency
Waveform frequency ≥ 4.9 MHz < 50 MHz A fraction of the waveform frequency
Waveform frequency ≥ 50 MHz No output
10 MHz reference clock out
Impedance
50 Ω, AC coupled
Amplitude
1.2 VP-P into 50 Ω load
Physical characteristics
Dimensions
Height
191.8 mm (7.55 in.)
Width
412.8 mm (16.25 in.)
Depth
143.3 mm (5.64 in.)
Weight
Net
4.7 kg (10.4 lb.)
Shipping
7.0 kg (15.4 lb.)
EMC, environment, and safety
Temperature
Operating
0 °C to +50 °C (32 °F to 122 °F)
Nonoperating
-30 °C to +70 °C (-22 °F to 158 °F)
Humidity
Operating
≤ 80%, 0 °C to 40 °C (32 °F to104 °F)

≤ 60%, > 40°C to 50°C (104 °F to 122 °F), noncondensing

Nonoperating
5% to 90%, < 40 °C (< 104 °F), noncondensing

5% to 80%, ≥ 40 °C to 60 °C (≥ 104 °F to 140 °F), noncondensing

5% to 40%, > 60 °C to 70 °C (> 140 °F to 158 °F), noncondensing

Altitude
Operating
Up to 3,000 m (9,842 ft.)
Nonoperating
Up to 12,000 m (39,370 ft.)
EMC compliance
EN61326-1:2013, EN 61326-2-1:2013

European Union
EU Council Directive 2004/108/EC
Safety
UL 61010-1:2004

CAN/CSA C22.2 No. 61010-1:2004

IEC 61010-1:2001

Over-temperature protection
Instrument is protected from over-temperature by turning off outputs

Related Products